Rolling bearing removal equipment and disassembly
Posted on

Home>Bearing knowledge>Removal equipment and disassembly of rolling bearings
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Rolling bearing removal equipment and disassembly

Source: Bearing network time: 2014-08-07
/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
The tumbling bearing is a combination of bearing shaft transformation. The ferrule and the tumbling body are finely machined. The bearing is before leaving the factory; the turret and the tumbling surface are not rusted; the raceway and the tumbling body are injected between the raceway and the tumbling body. Anti-rust oil or anti-rust grease. Therefore, the bearing equipment should be removed before cleaning. The bearings sealed with anti-rust oil can be directly removed by gasoline or fire oil, and rust-proof with thick oil or anti-rust grease; light mineral oil must be used first; For example, if 10# oil or transformer oil is heated to melt and cool the oil; then remove it with gasoline or kerosene. Bearings with dust cover or sealing ring on both sides; smooth grease has been added before leaving the factory; therefore, the equipment does not need to be removed. Bearings coated with smooth rust-proof grease; do not need to be removed from the equipment. During the process of removing the equipment; beware of foreign objects falling into the bearing; fine abrasive particles will cause wear between the roll and the raceway, Increase noise and oscillation.
There are two ways to install and disassemble the bearing. First, press the interference ferrule into the shaft or press it into the hole of the bearing housing. First, the inner diameter of the bearing is increased by heating the bearing; or the outer diameter of the bearing is reduced. When the pressurization method is selected, the mechanical force or hydraulic pressure is directly applied to the seat to be disassembled by special equipment; the loading and unloading force is never allowed to pass through the rolling body. Otherwise, the raceway and the tumbler surface indentation will be formed, and the noise and oscillation will be increased to cause damage. If heating or cooling is used for the assembly and disassembly, the heating temperature or cooling temperature should be strictly controlled. The strength of the outer surface of the bearing operation is affected by the metal surface gold. The influence of the phase arrangement layout and the excessive temperature will form a tempering effect. If the temperature is too high, the external appearance will be embrittled. Generally, the heating temperature should not exceed 100 °C; the cooling bottom temperature should not be below 50 °C. Be even.
Practice has proved that improper bearing equipment is one of the reasons for the premature failure of the bearing. It is not easy to install and remove the ferrule with interference; therefore, when depicting the support; it is necessary to think about how the bearing is assembled and disassembled and convenient. The problem of assembly and disassembly. The assembly and disassembly of large-sized bearings for heavy machinery often requires the depiction of special equipment. If the high-pressure oil is disassembled, it is necessary to draw the oil circuit, pipeline and pump.
Recommend to friends comments close window

Bearing related knowledge
Smooth rolling mill bearings
5 steps let you recognize the summary of the selection of genuine bearing bearings for imported bearings. The use of metal self-correcting materials on bearings (1)
NSK imported bearing accuracy grade common sense collection


This article links to http://
Please indicate China Bearing Network http://

Previous: Rolling mill bearing device and protection key Next: Static pressure imported bearings

Sds Hammer Drill Bit

Hcs Drill Bits For Wood-Sds Hammer Drill Bit

Type:Twist Drill Bit, SDS max, SDS plus

Use:Masonry Drilling, Masonry Drilling


• "+" carbide drill bits is made of quality alloy structured steel with special grade carbide tip, and brazed under the temperature of 850℃.

• Application:concrete ;clinker;masonry;stone

• Flute available :W flute;U flute;L flute

• Carbide: Cross(+) style carbide

• We can offer different finish : Galvanized finish, Nickel Plated finish, Black and white finish, black finish, Sandblasted finish.

1.Professional quality for efficient and fast hammer drilling in hard materials like concrete, granite, brick and other similar building materials.

2.Premium carbon steel with heat treatment improves core strength for maximum durability and extended life.

4.Copper braze material gives high heat resistance for reduced tip loss,Carbide tip securely embedded in the steel body.

5.U flute ensures fast, efficient removal of drilling dust and debris to increase speed and prevent clogging.

Sds Hammer Drill Bit,Sds Plus Hammer Drill For Cut,Rotary Hammer Drill For Concrete,Hammer Drill For Concrete

Changzhou Bomitools Co.,Ltd. , https://www.bomitools.com